; filament used = 1345.8mm (9.2cm3)
; total filament cost = 0.0
; avoid_crossing_perimeters = 1
; bed_shape = 0x18,245x18,245x258,0x258
; bed_temperature = 42
; before_layer_gcode =
; between_objects_gcode =
; bridge_acceleration = 0
; bridge_fan_speed = 100
; brim_connections_width = 0
; brim_width = 0
; complete_objects = 0
; cooling = 1
; default_acceleration = 0
; disable_fan_first_layers = 3
; duplicate_distance = 6
; end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
; end_gcode = M104 S0\nM140 S0\n; G91\nG92 Z0 E0 ; zero out Z and Extruder\nG1 E-0.5 F300\n;move Z up a bit and retract filament even more\nG1 Z+0.5 E-0.5 X0 Y210 F4500 ; move extruder & part to unload position\n; Steppers off\nM84 \n;Acceleration to default...\n;Acc printing\nM201 X1000 Y1000 Z1000\n;Acc travel\nM202 X1000 Y1000 Z1000\n;\nM300 S1800 P333 ; beep\nG4 P333 ; pause one-third second\nM300 S2400 P333 ; beep\nG4 P165 ; pause\nM300 S2660 P333\nG4 P80\nM300 S1800 P666 ; beep\nG4 P1 ; pause, End of custom "end.gcode" for RF1k\nM104 S130 ; set temp to 130 deg., enable filament removal\nM106 S255 ; keep fan on
; extruder_clearance_height = 20
; extruder_clearance_radius = 20
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 0.96
; fan_always_on = 1
; fan_below_layer_time = 60
; filament_colour = #FFFFFF
; filament_cost = 0
; filament_density = 0
; filament_diameter = 2.95,7
; filament_max_volumetric_speed = 0
; filament_notes = ""
; first_layer_acceleration = 0
; first_layer_bed_temperature = 54
; first_layer_extrusion_width = 0.62
; first_layer_speed = 70%
; first_layer_temperature = 222
; gcode_arcs = 0
; gcode_comments = 0
; gcode_flavor = reprap
; has_heatbed = 1
; infill_acceleration = 0
; infill_first = 0
; interior_brim_width = 0
; layer_gcode = ;M400\nM300 S2660 P233\n;G4 P1\nM300 S260 P120\nM300 S2400 P233
; max_fan_speed = 100
; max_print_speed = 80
; max_volumetric_speed = 0
; min_fan_speed = 40
; min_print_speed = 9
; min_skirt_length = 0.4
; notes =
; nozzle_diameter = 0.6
; only_retract_when_crossing_perimeters = 1
; ooze_prevention = 0
; output_filename_format = [input_filename_base]_[hour];[minute].gcode
; perimeter_acceleration = 0
; post_process =
; pressure_advance = 0
; printer_notes = ""
; resolution = 0.006
; retract_before_travel = 1
; retract_layer_change = 1
; retract_length = 1.6
; retract_length_toolchange = 4
; retract_lift = 0
; retract_lift_above = 0
; retract_lift_below = 0
; retract_restart_extra = 0.0002
; retract_restart_extra_toolchange = 0
; retract_speed = 90
; skirt_distance = 2
; skirt_height = 1
; skirts = 2
; slowdown_below_layer_time = 20
; spiral_vase = 0
; standby_temperature_delta = -5
; start_filament_gcode = "; Filament gcode\n"
...
...