ZAchse bleibt nicht stehen

[marmor]

Zum digit Wert, der in der Beschreibung angesprochen wurde:

F: 1042 digit

Der ist also unter 3000. Keine Ahnung was hier nicht passt.

[marmor]

Wollte ich gerade schreiben, aber bist ja selbst drauf gekommen...

Nur woran liegt es

[JoBo]

Ich muss mir die Beschreibung mal ziehen, Hab schon lange nicht mehr gefräst...

[marmor]

Ich habe mir jetzt von hier

http://www.rf1000.de/viewtopic.php?f=27&t=539&start=90

bis Seite 12 die Beiträge durchgelesen. Das könnte irgendwie auch bei mir zutreffen.

[JoBo]

OK, hab jetzt selbst mal einen Scan gemacht.

Hier der Auszug des Log vom Setzen des Start- und Endpunkts bis Abschluss des Scans:

Code: Alles auswählen

16:05:07.486 : N77 G28 X0 *75
16:05:11.247 : N78 G28 Y0 *69
16:05:25.664 : N79 G91 *15
16:05:25.664 : N80 G1 X50 F1800 *34
16:05:25.664 : N81 G90 *9
16:05:28.353 : N82 G91 *11
16:05:28.353 : N83 G1 Y50 F1800 *32
16:05:28.353 : N84 G90 *12
16:06:07.377 : setScanXYStart(): the new x/y start position is bigger than the current x/y end position, the x/y end position will be set to the new x/y start position
16:06:07.377 : setScanXYStart(): the new x/y start position has been set
16:06:07.377 : start: x = 50.00, y = 50.00 [mm]
16:06:07.377 : end: x = 50.00, y = 50.00 [mm]
16:06:24.417 : N85 G91 *12
16:06:24.417 : N86 G1 Y50 F1800 *37
16:06:24.417 : N87 G90 *15
16:06:26.721 : N88 G91 *1
16:06:26.721 : N89 G1 X50 F1800 *43
16:06:26.721 : N90 G90 *9
16:06:30.233 : setScanXYEnd(): the new x/y end position has been set
16:06:30.233 : start: x = 50.00, y = 50.00 [mm]
16:06:30.233 : end: x = 100.00, y = 100.00 [mm]
16:06:32.331 : setScanXYEnd(): the new x/y end position has been set
16:06:32.331 : start: x = 50.00, y = 50.00 [mm]
16:06:32.331 : end: x = 100.00, y = 100.00 [mm]
16:07:25.865 : scanWorkPart(): the scan has been started
16:07:25.865 : outputScanParameters(): current scan parameters:
16:07:25.865 : 2560.00;[steps];ZAXIS_STEPS_PER_MM
16:07:25.865 : 7619;[steps];g_nScanXStartSteps
16:07:25.865 : 1523;[steps];g_nScanXStepSizeSteps
16:07:25.865 : 33523;[steps];g_nScanXEndSteps
16:07:25.865 : 15238;[steps];g_nScanXMaxPositionSteps
16:07:25.865 : 7619;[steps];g_nScanYStartSteps
16:07:25.865 : 1523;[steps];g_nScanYStepSizeSteps
16:07:25.865 : 25904;[steps];g_nScanYEndSteps
16:07:25.865 : 15238;[steps];g_nScanYMaxPositionSteps
16:07:25.865 : -64;[steps];g_nScanHeatBedUpFastSteps
16:07:25.865 : -12;[steps];g_nScanHeatBedUpSlowSteps
16:07:25.865 : 1280;[steps];g_nScanHeatBedDownFastSteps
16:07:25.865 : 32;[steps];g_nScanHeatBedDownSlowSteps
16:07:25.865 : 5;[ms];g_nScanFastStepDelay
16:07:25.865 : 100;[ms];g_nScanSlowStepDelay
16:07:25.865 : 250;[ms];g_nScanIdleDelay
16:07:25.865 : 500;[digits];g_nScanContactPressureDelta
16:07:25.865 : 250;[digits];g_nScanRetryPressureDelta
16:07:25.865 : 0;[digits];g_nScanIdlePressureDelta
16:07:25.865 : 15;[-];g_nScanPressureReads
16:07:25.865 : 15;[digits];g_nScanPressureTolerance
16:07:25.865 : 15;[ms];g_nScanPressureReadDelay
16:07:39.286 : readIdlePressure(): pressure calibration: 0 / -208
16:07:40.038 : readIdlePressure(): idle pressure: -208
16:08:37.627 : scanWorkPart(): the z-origin has been determined
16:08:38.348 : EEPROM updated
16:08:39.882 : moveZDownFast(): -216
16:08:56.855 : moveZDownFast(): -219
16:09:11.605 : moveZDownFast(): -219
16:09:26.083 : moveZDownFast(): -218
16:09:40.512 : moveZDownFast(): -217
16:09:55.389 : moveZDownFast(): -218
16:10:09.818 : moveZDownFast(): -219
16:10:24.599 : moveZDownFast(): -221
16:10:41.460 : moveZDownFast(): -221
16:10:58.641 : moveZDownFast(): -223
16:11:15.550 : moveZDownFast(): -225
16:11:32.075 : moveZDownFast(): -223
16:11:47.864 : moveZDownFast(): -223
16:12:05.126 : moveZDownFast(): -224
16:12:22.306 : moveZDownFast(): -224
16:12:35.584 : moveZDownFast(): -223
16:12:49.965 : moveZDownFast(): -223
16:13:03.930 : moveZDownFast(): -222
16:13:17.912 : moveZDownFast(): -223
16:13:30.998 : moveZDownFast(): -224
16:13:48.163 : moveZDownFast(): -225
16:14:03.936 : moveZDownFast(): -224
16:14:21.117 : moveZDownFast(): -225
16:14:38.282 : moveZDownFast(): -224
16:14:54.758 : moveZDownFast(): -223
16:15:09.539 : moveZDownFast(): -221
16:15:27.408 : moveZDownFast(): -222
16:15:44.974 : moveZDownFast(): -221
16:16:01.851 : moveZDownFast(): -221
16:16:17.927 : moveZDownFast(): -221
16:16:31.509 : moveZDownFast(): -220
16:16:47.378 : moveZDownFast(): -216
16:17:06.750 : moveZDownFast(): -217
16:17:24.956 : moveZDownFast(): -217
16:17:42.983 : moveZDownFast(): -217
16:17:58.069 : moveZDownFast(): -216
16:18:12.434 : moveZDownFast(): -216
16:18:22.853 : scanWorkPart(): raw work part compensation matrix:
16:18:22.853 : front left ... front right
16:18:22.853 : ...        ...         ...
16:18:22.853 : back left  ...  back right
16:18:22.853 : ;6;0;50;59;69;79;89
16:18:22.853 : ;0;0;0;0;0;0;0
16:18:22.853 : ;50;0;-128;-124;-132;-132;-128
16:18:22.853 : ;59;0;-136;-148;-152;-144;-136
16:18:22.853 : ;69;0;-132;-148;-148;-144;-144
16:18:22.853 : ;79;0;-128;-140;-144;-136;-132
16:18:22.853 : ;89;0;-124;-132;-128;-128;-108
16:18:22.853 : offset = 0 [steps]0
16:18:22.853 : g_uZMatrixMaxX = 7
16:18:22.853 : g_uZMatrixMaxY = 7
16:18:22.853 : g_nActiveWorkPart = 1
16:18:22.853 : scan start: x = 50.00, y = 50.00 [mm]
16:18:22.853 : scan steps: x = 10.00, y = 10.00 [mm]
16:18:22.853 : scan end: x = 100.00, y = 100.00 [mm]
16:18:23.025 : scanWorkPart(): total scan time: 657 [s]
16:18:23.025 : scanWorkPart(): g_uZMatrixMaxY.1 = 8
16:18:23.025 : scanWorkPart(): g_uZMatrixMaxY.2 = 8
16:18:23.025 : scanWorkPart(): converted work part compensation matrix:
16:18:23.025 : front left ... front right
16:18:23.025 : ...        ...         ...
16:18:23.025 : back left  ...  back right
16:18:23.025 : ;6;0;50;59;69;79;89;245
16:18:23.025 : ;0;-128;-128;-124;-132;-132;-128;-128
16:18:23.025 : ;50;-128;-128;-124;-132;-132;-128;-128
16:18:23.025 : ;59;-136;-136;-148;-152;-144;-136;-136
16:18:23.025 : ;69;-132;-132;-148;-148;-144;-144;-144
16:18:23.025 : ;79;-128;-128;-140;-144;-136;-132;-132
16:18:23.025 : ;89;-124;-124;-132;-128;-128;-108;-108
16:18:23.025 : ;245;-124;-124;-132;-128;-128;-108;-108
16:18:23.025 : offset = -108 [steps]-108
16:18:23.025 : g_uZMatrixMaxX = 8
16:18:23.025 : g_uZMatrixMaxY = 8
16:18:23.025 : g_nActiveWorkPart = 1
16:18:23.025 : scan start: x = 50.00, y = 50.00 [mm]
16:18:23.025 : scan steps: x = 10.00, y = 10.00 [mm]
16:18:23.025 : scan end: x = 100.00, y = 100.00 [mm]
16:18:23.025 : saveCompensationMatrix(): valid data detected
16:18:24.606 : scanWorkPart(): the work part compensation matrix has been saved > 1
16:18:25.904 : scanWorkPart(): idle pressure at start: -208
16:18:25.921 : scanWorkPart(): idle pressure at stop: -207
16:18:25.921 : scanWorkPart(): the scan has been completed

Danach hab ich aus versehen die Werkseinstellungen angeklickt. Speichern müsste aber mit Setze Werkstück: 1 (bzw. 2,3...) gehen. Im Englischen Menü steht "Set Work Part:". Ich habe das mit der RF.01.10 gemacht.

[marmor]

Danke mal für den Hinweis der neuen Firmware.

Meine hatte ich ja vor 5 Tagen und die damalige Beta aufgespielt gehabt. Mit der jetzigen neuen Firmware hatte sich natürlich die Baudrate geändert gehabt und das mich wieder ein paar Haare verlieren lassen ...

Ich glaube, jetzt bei der neuen Firmware wurde der Scan gut beendet.

Code: Alles auswählen

17:28:37.713 : setScanXYStart(): the new x/y start position is bigger than the current x/y end position, the x/y end position will be set to the new x/y start position
17:28:37.713 : setScanXYStart(): the new x/y start position has been set
17:28:37.713 : start: x = 109.99, y = 94.00 [mm]
17:28:37.713 : end: x = 109.99, y = 94.00 [mm]
17:28:38.134 : N239 M105 *15
17:28:38.181 : ok 239
17:28:38.181 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:28:39.195 : wait
17:28:40.178 : wait
17:28:41.192 : N240 M105 *1
17:28:41.192 : wait
17:28:41.192 : ok 240
17:28:41.192 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:28:42.206 : wait
17:28:43.189 : wait
17:28:44.203 : wait
17:28:44.250 : N241 M105 *0
17:28:44.250 : ok 241
17:28:44.250 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:28:44.531 : N242 G91 *53
17:28:44.531 : N243 G1 X-10 F4800 *51
17:28:44.531 : N244 G90 *50
17:28:44.531 : ok 242
17:28:44.531 : ok 243
17:28:44.531 : ok 244
17:28:45.545 : wait
17:28:46.543 : wait
17:28:46.949 : N245 G91 *50
17:28:46.949 : N246 G1 X50 F4800 *31
17:28:46.949 : N247 G90 *49
17:28:46.949 : ok 245
17:28:46.949 : ok 246
17:28:46.949 : ok 247
17:28:47.307 : N248 M105 *9
17:28:47.307 : ok 248
17:28:47.354 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:28:48.306 : wait
17:28:49.304 : wait
17:28:50.318 : wait
17:28:50.365 : N249 M105 *8
17:28:50.381 : ok 249
17:28:50.381 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:28:51.363 : wait
17:28:52.377 : wait
17:28:53.360 : wait
17:28:53.423 : N250 M105 *0
17:28:53.438 : ok 250
17:28:53.438 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:28:54.421 : wait
17:28:55.435 : wait
17:28:56.418 : wait
17:28:56.480 : N251 M105 *1
17:28:56.480 : ok 251
17:28:56.480 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:28:57.479 : wait
17:28:58.493 : wait
17:28:59.475 : wait
17:28:59.538 : N252 M105 *2
17:28:59.538 : ok 252
17:28:59.538 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:00.536 : wait
17:29:01.566 : wait
17:29:01.847 : N253 G91 *53
17:29:01.847 : N254 G1 Y10 F4800 *25
17:29:01.847 : N255 G90 *50
17:29:01.862 : ok 253
17:29:01.862 : ok 254
17:29:01.862 : ok 255
17:29:02.595 : N256 M105 *6
17:29:02.595 : ok 256
17:29:02.595 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:03.609 : wait
17:29:04.592 : wait
17:29:05.606 : wait
17:29:05.653 : N257 M105 *7
17:29:05.653 : ok 257
17:29:05.653 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:06.667 : wait
17:29:07.353 : setScanXYEnd(): the new x/y end position has been set
17:29:07.353 : start: x = 109.99, y = 94.00 [mm]
17:29:07.353 : end: x = 150.00, y = 104.00 [mm]
17:29:07.821 : wait
17:29:08.711 : N258 M105 *8
17:29:08.711 : ok 258
17:29:08.726 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:09.709 : wait
17:29:10.707 : wait
17:29:11.721 : wait
17:29:11.768 : N259 M105 *9
17:29:11.784 : ok 259
17:29:11.784 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:12.767 : wait
17:29:13.781 : wait
17:29:14.015 : findZOrigin(): the search has been started
17:29:14.264 : findZOrigin(): nMinPressureContact = 587, nMaxPressureContact = 1587
17:29:14.826 : N260 M105 *3
17:29:14.888 : ok 260
17:29:14.888 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:15.980 : wait
17:29:17.010 : wait
17:29:17.883 : N261 M105 *2
17:29:18.008 : ok 261
17:29:18.008 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:19.100 : wait
17:29:20.192 : wait
17:29:20.941 : N262 M105 *1
17:29:20.941 : ok 262
17:29:20.941 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:22.049 : wait
17:29:23.078 : wait
17:29:23.999 : N263 M105 *0
17:29:24.061 : ok 263
17:29:24.061 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:25.169 : wait
17:29:26.276 : wait
17:29:27.056 : N264 M105 *7
17:29:27.134 : ok 264
17:29:27.134 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:28.289 : wait
17:29:29.396 : wait
17:29:30.114 : N265 M105 *6
17:29:30.129 : ok 265
17:29:30.145 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:31.237 : wait
17:29:32.329 : wait
17:29:33.171 : N266 M105 *5
17:29:33.203 : ok 266
17:29:33.218 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:34.357 : wait
17:29:35.449 : wait
17:29:36.229 : N267 M105 *4
17:29:36.323 : ok 267
17:29:36.323 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:37.415 : wait
17:29:38.522 : wait
17:29:39.287 : N268 M105 *11
17:29:39.396 : ok 268
17:29:39.396 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:40.410 : wait
17:29:41.517 : wait
17:29:42.344 : N269 M105 *10
17:29:42.953 : EEPROM updated
17:29:42.968 : X:151.04 Y:104.00 Z:80.00 E:0.00
17:29:43.405 : ok 269
17:29:43.421 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:44.559 : wait
17:29:45.402 : N270 M105 *2
17:29:45.402 : ok 270
17:29:45.402 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:46.416 : wait
17:29:47.399 : wait
17:29:48.413 : wait
17:29:48.459 : N271 M105 *3
17:29:48.459 : ok 271
17:29:48.459 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:49.473 : wait
17:29:50.503 : wait
17:29:51.501 : wait
17:29:51.517 : N272 M105 *0
17:29:51.517 : ok 272
17:29:51.533 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:52.515 : wait
17:29:53.514 : wait
17:29:54.528 : wait
17:29:54.575 : N273 M105 *1
17:29:54.590 : ok 273
17:29:54.590 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:55.573 : wait
17:29:56.587 : wait
17:29:57.570 : wait
17:29:57.632 : N274 M105 *6
17:29:57.648 : ok 274
17:29:57.648 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:29:58.631 : wait
17:29:59.645 : wait
17:30:00.627 : wait
17:30:00.705 : N275 M105 *7
17:30:00.705 : ok 275
17:30:00.705 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:01.704 : wait
17:30:02.718 : wait
17:30:03.716 : wait
17:30:03.763 : N276 M105 *4
17:30:03.763 : ok 276
17:30:03.763 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:04.761 : wait
17:30:05.775 : wait
17:30:06.774 : wait
17:30:06.821 : N277 M105 *5
17:30:06.821 : ok 277
17:30:06.821 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:07.835 : wait
17:30:08.817 : wait
17:30:09.831 : wait
17:30:09.878 : N278 M105 *10
17:30:09.878 : ok 278
17:30:09.878 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:10.892 : wait
17:30:11.875 : wait
17:30:12.889 : wait
17:30:12.936 : N279 M105 *11
17:30:12.967 : ok 279
17:30:12.967 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:13.950 : wait
17:30:14.964 : wait
17:30:15.978 : wait
17:30:15.993 : N280 M105 *13
17:30:16.009 : ok 280
17:30:16.009 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:16.992 : wait
17:30:18.006 : wait
17:30:18.989 : wait
17:30:19.051 : N281 M105 *12
17:30:19.067 : ok 281
17:30:19.067 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:20.049 : wait
17:30:21.063 : wait
17:30:22.046 : wait
17:30:22.109 : N282 M105 *15
17:30:22.109 : ok 282
17:30:22.109 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:23.107 : wait
17:30:24.121 : wait
17:30:25.119 : wait
17:30:25.166 : N283 M105 *14
17:30:25.166 : ok 283
17:30:25.166 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:26.180 : wait
17:30:27.163 : wait
17:30:28.177 : wait
17:30:28.224 : N284 M105 *9
17:30:28.239 : ok 284
17:30:28.239 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:29.238 : wait
17:30:30.236 : wait
17:30:31.250 : wait
17:30:31.281 : N285 M105 *8
17:30:31.281 : ok 285
17:30:31.281 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:32.295 : wait
17:30:33.278 : wait
17:30:34.292 : wait
17:30:34.339 : N286 M105 *11
17:30:34.339 : ok 286
17:30:34.355 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:35.338 : wait
17:30:36.352 : wait
17:30:37.350 : wait
17:30:37.397 : N287 M105 *10
17:30:37.412 : ok 287
17:30:37.412 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:38.395 : wait
17:30:39.409 : wait
17:30:40.408 : wait
17:30:40.454 : N288 M105 *5
17:30:40.470 : ok 288
17:30:40.470 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:41.453 : wait
17:30:42.467 : wait
17:30:43.450 : wait
17:30:43.512 : N289 M105 *4
17:30:43.512 : ok 289
17:30:43.528 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:44.510 : wait
17:30:45.524 : wait
17:30:46.523 : wait
17:30:46.570 : N290 M105 *12
17:30:46.570 : ok 290
17:30:46.570 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:47.584 : wait
17:30:48.566 : wait
17:30:49.580 : wait
17:30:49.627 : N291 M105 *13
17:30:49.627 : ok 291
17:30:49.627 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:50.641 : wait
17:30:51.624 : wait
17:30:52.638 : wait
17:30:52.685 : N292 M105 *14
17:30:52.685 : ok 292
17:30:52.685 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:53.699 : wait
17:30:54.682 : wait
17:30:55.696 : wait
17:30:55.742 : N293 M105 *15
17:30:55.742 : ok 293
17:30:55.758 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:56.756 : wait
17:30:57.755 : wait
17:30:58.800 : N294 M105 *8
17:30:58.800 : wait
17:30:58.800 : ok 294
17:30:58.816 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:30:59.798 : wait
17:31:00.812 : wait
17:31:01.811 : wait
17:31:01.858 : N295 M105 *9
17:31:01.873 : ok 295
17:31:01.873 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:02.856 : wait
17:31:03.870 : wait
17:31:04.853 : wait
17:31:04.915 : N296 M105 *10
17:31:04.931 : ok 296
17:31:04.931 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:05.914 : wait
17:31:06.928 : wait
17:31:07.926 : wait
17:31:07.973 : N297 M105 *11
17:31:07.973 : ok 297
17:31:07.973 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:08.987 : wait
17:31:09.985 : wait
17:31:10.984 : wait
17:31:11.030 : N298 M105 *4
17:31:11.030 : ok 298
17:31:11.030 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:12.044 : wait
17:31:13.027 : wait
17:31:14.057 : wait
17:31:14.088 : N299 M105 *5
17:31:14.088 : ok 299
17:31:14.088 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:15.102 : wait
17:31:16.085 : wait
17:31:17.099 : wait
17:31:17.146 : N300 M105 *4
17:31:17.146 : ok 300
17:31:17.161 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:17.894 : scanWorkPart(): the scan has been started
17:31:17.894 : outputScanParameters(): current scan parameters:
17:31:17.894 : 2560.00;[steps];ZAXIS_STEPS_PER_MM
17:31:17.894 : 16761;[steps];g_nScanXStartSteps
17:31:17.894 : 3047;[steps];g_nScanXStepSizeSteps
17:31:17.894 : 33523;[steps];g_nScanXEndSteps
17:31:17.894 : 22857;[steps];g_nScanXMaxPositionSteps
17:31:17.894 : 14323;[steps];g_nScanYStartSteps
17:31:17.894 : 3047;[steps];g_nScanYStepSizeSteps
17:31:17.894 : 25904;[steps];g_nScanYEndSteps
17:31:17.894 : 15847;[steps];g_nScanYMaxPositionSteps
17:31:17.894 : -64;[steps];g_nScanHeatBedUpFastSteps
17:31:17.894 : -12;[steps];g_nScanHeatBedUpSlowSteps
17:31:17.894 : 1280;[steps];g_nScanHeatBedDownFastSteps
17:31:17.894 : 32;[steps];g_nScanHeatBedDownSlowSteps
17:31:17.894 : 5;[ms];g_nScanFastStepDelay
17:31:17.894 : 100;[ms];g_nScanSlowStepDelay
17:31:17.894 : 250;[ms];g_nScanIdleDelay
17:31:17.894 : 500;[digits];g_nScanContactPressureDelta
17:31:17.894 : 250;[digits];g_nScanRetryPressureDelta
17:31:17.894 : 0;[digits];g_nScanIdlePressureDelta
17:31:17.894 : 15;[-];g_nScanPressureReads
17:31:17.894 : 15;[digits];g_nScanPressureTolerance
17:31:17.894 : 15;[ms];g_nScanPressureReadDelay
17:31:18.144 : wait
17:31:19.158 : wait
17:31:20.141 : wait
17:31:20.203 : N301 M105 *5
17:31:20.203 : ok 301
17:31:23.261 : N302 M105 *6
17:31:23.261 : ok 302
17:31:26.318 : N303 M105 *7
17:31:29.392 : N304 M105 *0
17:31:30.000 : X:0.00 Y:0.00 Z:110.00 E:0.00
17:31:30.000 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:30.000 : ok 303
17:31:30.000 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:30.000 : ok 304
17:31:30.000 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:30.000 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:30.998 : wait
17:31:31.981 : wait
17:31:32.434 : N305 M105 *1
17:31:32.434 : ok 305
17:31:32.434 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:32.839 : readIdlePressure(): pressure calibration: 0 / 1080
17:31:33.572 : readIdlePressure(): idle pressure: 1078
17:31:33.572 : wait
17:31:34.602 : wait
17:31:35.491 : N306 M105 *2
17:31:35.585 : ok 306
17:31:35.585 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:36.708 : wait
17:31:37.816 : wait
17:31:38.549 : N307 M105 *3
17:31:38.564 : ok 307
17:31:38.564 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:39.672 : wait
17:31:40.702 : wait
17:31:41.606 : N308 M105 *12
17:31:41.700 : ok 308
17:31:41.700 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:42.808 : wait
17:31:43.900 : wait
17:31:44.664 : N309 M105 *13
17:31:44.789 : ok 309
17:31:44.789 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:45.943 : wait
17:31:47.035 : wait
17:31:47.722 : N310 M105 *5
17:31:47.784 : ok 310
17:31:47.800 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:48.907 : wait
17:31:50.015 : wait
17:31:50.779 : N311 M105 *4
17:31:50.873 : ok 311
17:31:50.888 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:52.027 : wait
17:31:53.150 : wait
17:31:53.837 : N312 M105 *7
17:31:53.899 : ok 312
17:31:53.899 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:55.007 : wait
17:31:56.114 : wait
17:31:56.894 : N313 M105 *6
17:31:56.988 : ok 313
17:31:56.988 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:31:58.142 : wait
17:31:59.250 : wait
17:31:59.952 : N314 M105 *1
17:31:59.999 : ok 314
17:31:59.999 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:01.122 : wait
17:32:02.214 : wait
17:32:03.010 : N315 M105 *0
17:32:03.088 : ok 315
17:32:03.103 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:04.242 : wait
17:32:05.350 : wait
17:32:06.067 : N316 M105 *3
17:32:06.114 : ok 316
17:32:06.114 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:07.206 : wait
17:32:08.314 : wait
17:32:09.125 : N317 M105 *2
17:32:09.187 : ok 317
17:32:09.203 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:10.342 : wait
17:32:11.449 : wait
17:32:12.182 : N318 M105 *13
17:32:12.198 : ok 318
17:32:12.198 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:13.321 : wait
17:32:14.429 : wait
17:32:15.240 : N319 M105 *12
17:32:15.287 : ok 319
17:32:15.302 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:16.441 : wait
17:32:17.564 : wait
17:32:18.298 : N320 M105 *6
17:32:18.313 : ok 320
17:32:18.329 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:19.421 : wait
17:32:20.513 : wait
17:32:21.355 : N321 M105 *7
17:32:21.402 : ok 321
17:32:21.402 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:22.556 : wait
17:32:23.648 : wait
17:32:24.413 : N322 M105 *4
17:32:24.538 : ok 322
17:32:24.538 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:25.645 : wait
17:32:26.737 : wait
17:32:27.470 : N323 M105 *5
17:32:27.502 : ok 323
17:32:27.517 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:28.641 : wait
17:32:29.764 : wait
17:32:30.528 : N324 M105 *2
17:32:30.637 : ok 324
17:32:30.637 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:31.745 : wait
17:32:32.853 : wait
17:32:33.586 : N325 M105 *3
17:32:33.601 : ok 325
17:32:33.617 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:34.756 : wait
17:32:35.863 : wait
17:32:36.643 : N326 M105 *0
17:32:36.737 : ok 326
17:32:36.737 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:37.845 : wait
17:32:38.952 : wait
17:32:39.701 : N327 M105 *1
17:32:39.701 : ok 327
17:32:39.732 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:40.855 : wait
17:32:41.979 : wait
17:32:42.759 : N328 M105 *14
17:32:42.837 : ok 328
17:32:42.837 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:43.960 : wait
17:32:45.067 : wait
17:32:45.816 : N329 M105 *15
17:32:45.925 : ok 329
17:32:45.941 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:46.971 : wait
17:32:48.016 : wait
17:32:48.016 : scanWorkPart(): the z-origin has been determined
17:32:48.702 : EEPROM updated
17:32:48.702 : X:109.99 Y:94.00 Z:80.33 E:0.00
17:32:48.874 : N330 M105 *7
17:32:50.293 : ok 330
17:32:50.293 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:50.559 : moveZDownFast(): 1067
17:32:51.541 : wait
17:32:51.931 : N331 M105 *6
17:32:52.150 : ok 331
17:32:52.150 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:53.429 : wait
17:32:54.661 : wait
17:32:54.989 : N332 M105 *5
17:32:55.301 : ok 332
17:32:55.301 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:56.533 : wait
17:32:58.047 : N333 M105 *4
17:32:58.171 : ok 333
17:32:58.187 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:32:59.497 : wait
17:33:01.104 : N334 M105 *3
17:33:01.213 : ok 334
17:33:01.229 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:02.680 : wait
17:33:03.725 : wait
17:33:04.162 : N335 M105 *2
17:33:04.458 : ok 335
17:33:04.458 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:05.878 : wait
17:33:06.939 : wait
17:33:07.219 : N336 M105 *1
17:33:07.656 : ok 336
17:33:07.672 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:09.622 : wait
17:33:09.887 : moveZDownFast(): 1067
17:33:10.277 : N337 M105 *0
17:33:10.293 : ok 337
17:33:10.293 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:11.369 : wait
17:33:12.633 : wait
17:33:13.335 : N338 M105 *15
17:33:13.584 : ok 338
17:33:13.584 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:14.832 : wait
17:33:16.065 : wait
17:33:16.392 : N339 M105 *14
17:33:16.392 : ok 339
17:33:16.392 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:18.015 : wait
17:33:19.356 : wait
17:33:19.450 : N340 M105 *0
17:33:19.933 : ok 340
17:33:19.949 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:21.088 : wait
17:33:22.211 : wait
17:33:22.507 : N341 M105 *1
17:33:22.866 : ok 341
17:33:22.882 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:23.943 : wait
17:33:25.066 : wait
17:33:25.565 : N342 M105 *2
17:33:26.142 : ok 342
17:33:26.142 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:28.030 : wait
17:33:28.295 : moveZDownFast(): 1083
17:33:28.623 : N343 M105 *3
17:33:28.623 : ok 343
17:33:28.638 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:29.793 : wait
17:33:31.056 : wait
17:33:31.680 : N344 M105 *4
17:33:31.992 : ok 344
17:33:31.992 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:33.240 : wait
17:33:34.473 : wait
17:33:34.738 : N345 M105 *5
17:33:34.816 : ok 345
17:33:34.816 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:36.095 : wait
17:33:37.405 : wait
17:33:37.795 : N346 M105 *6
17:33:38.076 : ok 346
17:33:38.076 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:39.808 : wait
17:33:40.853 : N347 M105 *7
17:33:41.243 : ok 347
17:33:41.243 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:42.319 : wait
17:33:43.770 : wait
17:33:43.911 : N348 M105 *8
17:33:44.113 : ok 348
17:33:44.113 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:45.533 : wait
17:33:46.594 : wait
17:33:46.968 : N349 M105 *9
17:33:46.968 : ok 349
17:33:46.984 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:33:48.247 : wait
17:33:48.528 : moveZDownFast(): 1091
17:33:49.667 : wait
17:33:50.026 : N350 M105 *1
17:33:50.104 : ok 350
17:33:53.083 : N351 M105 *0
17:33:53.099 : ok 351
17:33:56.141 : N352 M105 *3
17:33:59.214 : N353 M105 *2
17:34:00.447 : X:0.00 Y:0.00 Z:125.30 E:0.00
17:34:00.447 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:00.447 : ok 352
17:34:00.447 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:00.447 : ok 353
17:34:00.447 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:00.447 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:00.493 : scanWorkPart(): raw work part compensation matrix:
17:34:00.493 : front left ... front right
17:34:00.493 : ...        ...         ...
17:34:00.493 : back left  ...  back right
17:34:00.493 : offset = -32000 [steps]-32000
17:34:00.493 : g_uZMatrixMaxX = 4
17:34:00.493 : g_uZMatrixMaxY = 0
17:34:00.493 : g_nActiveWorkPart = 1
17:34:00.493 : scan start: x = 109.99, y = 94.00 [mm]
17:34:00.493 : scan steps: x = 20.00, y = 20.00 [mm]
17:34:00.493 : scan end: x = 150.00, y = 104.00 [mm]
17:34:00.649 : scanWorkPart(): total scan time: 162 [s]
17:34:00.712 : prepareCompensationMatrix(): invalid y dimension detected: 0 (max expected: 25)
17:34:00.712 : scanWorkPart(): g_uZMatrixMaxY.1 = 0
17:34:00.712 : scanWorkPart(): g_uZMatrixMaxY.2 = 0
17:34:00.712 : scanWorkPart(): converted work part compensation matrix:
17:34:00.712 : front left ... front right
17:34:00.712 : ...        ...         ...
17:34:00.712 : back left  ...  back right
17:34:00.712 : offset = -32000 [steps]-32000
17:34:00.712 : g_uZMatrixMaxX = 4
17:34:00.712 : g_uZMatrixMaxY = 0
17:34:00.712 : g_nActiveWorkPart = 1
17:34:00.712 : scan start: x = 109.99, y = 94.00 [mm]
17:34:00.712 : scan steps: x = 20.00, y = 20.00 [mm]
17:34:00.712 : scan end: x = 150.00, y = 104.00 [mm]
17:34:00.712 : saveCompensationMatrix(): invalid data detected ( 6 / 4 / 0 )0
17:34:02.256 : N354 M105 *5
17:34:05.329 : N355 M105 *4
17:34:08.387 : N356 M105 *7
17:34:11.445 : N357 M105 *6
17:34:14.502 : N358 M105 *9
17:34:14.580 : scanWorkPart(): the work part compensation matrix has been saved > 1
17:34:14.580 : ok 354
17:34:14.596 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:14.643 : ok 355
17:34:14.643 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:14.643 : ok 356
17:34:14.643 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:14.643 : ok 357
17:34:14.643 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:14.643 : ok 358
17:34:14.643 : T:0.00 /0 B:0.00 /0 B@:0 @:0
17:34:15.875 : scanWorkPart(): idle pressure at start: 1078
17:34:15.875 : scanWorkPart(): idle pressure at stop: 1030
17:34:15.875 : wait
17:34:15.875 : scanWorkPart(): the scan has been completed

Dann werde ich es jetzt mal speichern und weiter probieren. Danke

[marmor]

Was ich auch drauf kam, wie ihr geschrieben habt, auch wenn ich Z orign setze, das es der RF1000 am Anfang setzt und ich da besser nicht den Fräser einschalte. Dann setzt er den z orign.

Nur dann sieht es so aus:

Code: Alles auswählen

17:43:13.843 : N577 G91 *52
17:43:13.846 : N578 M3115 *63
17:43:13.846 : N579 M3130 *57
17:43:13.846 : N580 M400 *10
17:43:13.846 : N581 M3070 S1 *121
17:43:13.846 : N582 M117 Enable Miller *25
17:43:13.846 : N583 M3071 *56
17:43:13.846 : N584 M3141 *61
17:43:13.846 : N585 G90 *56
17:43:13.846 : N586 G17 *52
17:43:13.849 : N587 G0 Z10 *120
17:43:13.856 : ok 577
17:43:13.856 : ok 578
17:43:13.856 : N588 M117 ETE 1m 34s *93
17:43:13.872 : setOrigin(): the origin can not be set because the home position is unknown
17:43:13.872 : ok 579
17:43:13.872 : ok 580
17:43:13.872 : ok 581
17:43:13.902 : N589 G0 X1.8398 Y6.8203 *8
17:43:13.906 : N590 G0 Z1 *78
17:43:13.968 : findZOrigin(): the search has been started
17:43:14.208 : findZOrigin(): nMinPressureContact = 562, nMaxPressureContact = 1562
17:43:53.286 : EEPROM updated
17:43:53.286 : X:120.00 Y:100.00 Z:0.00 E:0.00
17:43:54.987 : ok 582
17:43:54.987 : N591 M105 *10
17:43:54.987 : N592 M117 ETE 1m 32s *80
17:43:55.018 : ok 583
17:43:55.018 : ok 584
17:43:55.018 : N593 M117 ETE 1m 32s *81

Enable Miller stimmt in der Praxis nicht, ich hatte ihn ausgeschaltet.

Also was ich jetzt tat:

An alle Home Punkte fahren
Beim Werkstück X/Y Start und Endpunkte setzten. Einen Werkstückscan durchführen. (dabei hat er an zwei Positionen das Werkstück berüht, was in Ordnung ist bei alle 20 mm und einem 40*10 Werkstück. (meines ist Eben)

Nach dem Scan mit dem Fräser wieder zum Werkstück fahren.

Das Programm gestartet (nicht den Fräser). Es wurde Wieder Z Orign gesetzt, hinauf (vom Werkstück weg) gefahren und dort steht jetzt der Fräser....

[marmor]

Also auf 3 Fehler kam ich mit eurer Hilfe schon drauf. Danke!

1) jedes Mal alle Achsen auf Home fahren
2) ich hatte seit 3 Tagen nicht mehr die aktuelle Firmware
3) Den Fräser nicht gleich einschalten

Nur funktionieren tut es noch immer nicht.

Das mit dem Speichern Set Work Part 1 usw. Da kann ich drauf drücken, dann kommt ein Stern. Ich kann die Zahlen ändern und wieder zurück.

[marmor]

Nachdem sich 30 min gar nichts getan hatte, habe ich den Notstop gedrückt, da kam dann noch der Log raus:

Code: Alles auswählen

18:17:36.976 : No start signal detected - forcing start
18:17:36.992 : N1 M110 *2
18:17:36.992 : N2 M115 *4
18:17:36.992 : N3 M105 *4
18:17:36.992 : N4 M114 *3
18:17:37.008 : N5 M111 S6 *66
18:17:37.008 : N6 T0 *28
18:17:37.008 : N7 M20 *54
18:17:37.008 : N8 M80 *51
18:17:37.008 : N9 M105 *14
18:17:37.242 : Info:External Reset
18:17:37.242 : Free RAM:1930
18:17:39.363 : SD init fail
18:17:39.363 : restoreDefaultScanParameters(): the default scan parameters have been restored
18:17:39.379 : TargetExtr0:0
18:17:39.379 : ok
18:17:39.441 : ok 2
18:17:39.441 : FIRMWARE_NAME:Repetier_RF.01.10 FIRMWARE_URL:https://github.com/RF1000/RF-Firmware/ PROTOCOL_VERSION:1.0 MACHINE_TYPE:Mendel EXTRUDER_COUNT:1 REPETIER_PROTOCOL:2
18:17:39.457 : Milling time:0 days 0 hours 0 min
18:17:39.457 : N10 M220 S100 *112
18:17:39.457 : ok 3
18:17:39.457 : N11 M221 S100 *112
18:17:39.457 : N12 M111 S6 *116
18:17:39.457 : N13 T0 *40
18:17:39.457 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:39.457 : ok 4
18:17:39.457 : X:0.00 Y:0.00 Z:0.00 E:0.00
18:17:39.457 : ok 5
18:17:39.457 : ok 6
18:17:39.457 : ok 7
18:17:39.457 : Begin file list
18:17:39.457 : End file list
18:17:39.457 : ok 8
18:17:39.457 : ok 9
18:17:39.457 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:39.472 : ok 10
18:17:39.472 : SpeedMultiply:100
18:17:39.472 : ok 11
18:17:39.472 : FlowMultiply:100
18:17:39.472 : ok 12
18:17:39.472 : ok 13
18:17:40.034 : N14 M105 *50
18:17:40.034 : ok 14
18:17:40.034 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:41.048 : wait
18:17:42.031 : wait
18:17:43.045 : wait
18:17:43.092 : N15 M105 *51
18:17:43.092 : ok 15
18:17:43.092 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:44.106 : wait
18:17:45.088 : wait
18:17:46.102 : wait
18:17:46.149 : N16 M105 *48
18:17:46.149 : ok 16
18:17:46.149 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:47.163 : wait
18:17:48.146 : wait
18:17:49.160 : wait
18:17:49.207 : N17 M105 *49
18:17:49.207 : ok 17
18:17:49.222 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:50.205 : wait
18:17:51.219 : wait
18:17:52.218 : wait
18:17:52.264 : N18 M105 *62
18:17:52.280 : ok 18
18:17:52.280 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:53.263 : wait
18:17:54.277 : wait
18:17:55.260 : wait
18:17:55.322 : N19 M105 *63
18:17:55.338 : ok 19
18:17:55.338 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:56.320 : wait
18:17:57.334 : wait
18:17:58.317 : wait
18:17:58.380 : N20 M105 *53
18:17:58.380 : ok 20
18:17:58.380 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:17:59.378 : wait
18:18:00.392 : wait
18:18:01.390 : wait
18:18:01.437 : N21 M105 *52
18:18:01.437 : ok 21
18:18:01.437 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:18:02.436 : wait
18:18:03.434 : wait
18:18:04.448 : wait
18:18:04.495 : N22 M105 *55
18:18:04.495 : ok 22
18:18:04.495 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:18:05.509 : wait
18:18:06.492 : wait
18:18:07.506 : wait
18:18:07.552 : N23 M105 *54
18:18:07.552 : ok 23
18:18:07.552 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:18:08.566 : wait
18:18:09.549 : wait
18:18:10.563 : wait
18:18:10.610 : N24 M105 *49
18:18:10.610 : ok 24
18:18:10.626 : T:0.00 /0 B:0.00 /0 B@:0 @:0
18:18:11.608 : wait
18:18:12.607 : wait
18:18:13.621 : wait
18:18:13.668 : N25 M105 *48
18:18:13.683 : ok 25
18:18:13.683 : T:0.00 /0 B:0.00 /0 B@:0 @:0

[JoBo]

Das Programm gestartet (nicht den Fräser). Es wurde Wieder Z Orign gesetzt, hinauf (vom Werkstück weg) gefahren und dort steht jetzt der Fräser....

Kam dann die Meldung "Starte Fräser" (bzw. "Start Miller")? Falls du noch Menü für die Z-Kompensation bist, musst du da raus, auf die oberste Ebene, sonst sieht du die Meldung nicht.
Falls, die Meldung kommt, den Fräser starten und dann die Play Taste drücken, da der Drucker an dieser Stelle pausiert.